Motorcycle Small Engine NC II Practice Questions - TESDA Motorcycle Small Engine Servicing NC II Competency Assessment Exam - Motorcycle Small Engine NC II Practice Questions - TESDA Motorcycle Small Engine Servicing NC II Competency Assessment Exam

Question 1

What is the standard procedure for cleaning a polyurethane foam air filter element used in most small underbone motorcycles?

Wash with kerosene or a high-flash point solvent, squeeze out the excess, dry it, and then saturate with clean engine oil and squeeze out excess oil. Blow with high-pressure compressed air from the inside out and wipe the exterior surface with a dry cloth. Wash with gasoline, wring it out tightly, and install it immediately to allow the fuel to clean the carburetor. Soak in hot soapy water, wring it out to dry, and install it dry without applying any oil.

Correct Answer:

Wash with kerosene or a high-flash point solvent, squeeze out the excess, dry it, and then saturate with clean engine oil and squeeze out excess oil.

Question 2

When checking the engine oil level of a motorcycle using a dipstick, which of the following describes the correct measurement procedure?

Warm up the engine, shut it off, wait a few minutes, hold the motorcycle upright on level ground, wipe the dipstick, insert it without screwing it in, and check the level. Measure the oil immediately after a long ride while the engine is running and the motorcycle is on its side stand. Wipe the dipstick, screw it in fully, hold the motorcycle on its side stand, unscrew it, and read the level. Measure the oil while the engine is cold, with the motorcycle leaning on the side stand, inserting the dipstick without wiping it.

Correct Answer:

Warm up the engine, shut it off, wait a few minutes, hold the motorcycle upright on level ground, wipe the dipstick, insert it without screwing it in, and check the level.

Question 3

What is the recommended range of drive chain slack for a standard underbone motorcycle, and where should this measurement be taken?

20 mm to 30 mm, measured at the midpoint of the lower chain run between the front and rear sprockets. 5 mm to 10 mm, measured directly underneath the rear sprocket. 40 mm to 50 mm, measured at the top run of the chain near the swingarm pivot. 10 mm to 15 mm, measured on the lower run while the rider is sitting on the motorcycle.

Correct Answer:

20 mm to 30 mm, measured at the midpoint of the lower chain run between the front and rear sprockets.

Question 4

When inspecting a conventional flooded lead-acid battery, what liquid should be added if the electrolyte level is below the lower limit mark?

Distilled water Tap water Battery acid (diluted sulfuric acid) Engine coolant mixed with water

Correct Answer:

Distilled water

Question 5

Which tool should be used to measure the gap of a spark plug to ensure it meets manufacturer specifications?

Wire-type or flat feeler gauge Vernier caliper Steel dial indicator Thread pitch gauge

Correct Answer:

Wire-type or flat feeler gauge

Question 1

Exam overview

About this Exam

Prepare with the Motorcycle Small Engine NC II Practice Questions - TESDA Motorcycle Small Engine Servicing NC II Competency Assessment Exam practice quiz. This question bank includes 100 questions covering engine, motorcycle, cylinder, piston, and standard. Use it to review important concepts, identify knowledge gaps, and build confidence for the related exam, course, or assessment.

More details

Additional Information

Motorcycle Small Engine NC II Practice Questions - TESDA Motorcycle Small Engine Servicing NC II Competency Assessment Exam

This practice set contains 100 questions from the matching question bank and focuses on engine, motorcycle, cylinder, piston, and standard. Work through each question carefully, review the provided solutions, and revisit topics that need more study before your next attempt.

This is an independent study resource intended for practice and review; it is not an official examination or an endorsement by any organization named in the title.

Quiz information

Frequently Asked Questions

The complete question count is available after full access is unlocked.

No fixed duration is currently configured for this quiz.

Question explanations are included where they are available in the quiz content, helping you review the reasoning after answering.

Yes. You can retake the practice test again as you continue studying during your available access period.

After your access is confirmed, you can continue into the complete practice exam from this quiz flow.

Unless explicitly stated otherwise, this page provides independent practice material for study and exam preparation and is not the official examination itself.

Keep studying

Correct Answer:

Correct Answer:

Correct Answer:

Correct Answer:

Correct Answer:

About this Exam

Additional Information

Motorcycle Small Engine NC II Practice Questions - TESDA Motorcycle Small Engine Servicing NC II Competency Assessment Exam

Frequently Asked Questions

Related Questions

10th Brigade Engineer Battalion (10BEB) Board Practice Exam

2nd Class Power Engineering (2A1) Practice Exam

2nd Class Power Engineering 2A3 Practice Exam

2nd Class Power Engineering (2B1) Practice Exam

2nd Class Power Engineering 2B2 Practice Exam

2nd Class Power Engineering 2B3 Practice Exam