Register
Question 1
During a pre-trip inspection, which belts should you inspect?
Correct Answer:
All of The Above
Explanation:
In a pre-trip you check every belt that could affect the vehicle’s safety and performance, because a failure anywhere along the belt drive can leave you stranded or cause a safety issue. The belts you inspect include the ones powering essential systems like the power steering, water pump, and alternator, since each of those components is crucial: power steering for steering assist, the water pump for engine cooling, and the alternator for charging the battery. Some engines use a single serpentine belt that drives several accessories, while others have multiple belts; in either case, you inspect all belts present. Look for cracks, fraying, glazing, oil contamination, or any looseness, and check that the belt tension is correct and the pulleys align properly. If any belt shows wear or damage, it should be replaced before driving.
Question 2
Vehicles wider than what width require clearance lights?
Correct Answer:
2.05m
Explanation:
Clearance lights are there to show other drivers how wide a vehicle is, especially in dim light or poor visibility. In Alberta, the rule is that vehicles wider than 2.05 meters must have these lights. That width, about 80 inches, is used because it marks out a vehicle size that is noticeably wider than standard cars, helping maintain safety on the road. The other options are outside the practical threshold: 1.55 meters and 1.20 meters are typical widths for ordinary vehicles and don’t require clearance lights, while 3.05 meters is far wider than normal road vehicles and would be governed by other regulations and equipment. So the width that triggers clearance lights is 2.05 meters.
Question 3
Low speed off-tracking
Correct Answer:
Is when the rear tires are pulled inward of the steering path
Explanation:
When a vehicle with multiple axles turns, the rear tires don’t follow the same path as the front tires. They tend to follow a smaller circle, staying closer to the center of the curve. At low speed, this effect is noticeable because the front wheels swing through a tighter arc for the same steering input, pulling the rear closer to the curve’s inside. This inward pull of the rear tires relative to the steering path is what low speed off-tracking describes. The other ideas—just turning in a direction, or relying on centrifugal force, or the rear tires moving outward—don’t capture this geometric behavior of the rear wheels during a turn.
Question 4
What should you do if you lose sight of the guide while backing?
Correct Answer:
Stop immediately
Explanation:
When backing, you must have a clear view of the guide and the area behind you. If you lose sight of the person guiding you, the safest move is to stop immediately. This stops the vehicle before you drift into an obstacle or into the guide’s path, and it lets you re-establish communication and visibility—either by re-seeing the guide, moving to a position where you can see them, or having the spotter guide you from a better angle. Tapping the horn won’t restore visibility or communication, adjusting mirrors while still moving won’t fix the immediate risk, and slowing down without stopping still leaves you without a confirmed view of your surroundings. Stop to reassess, then proceed only when you can clearly see and coordinate with the guide.
Question 5
What does the reserved lane sign indicate about traffic flow in that lane?
Correct Answer:
Vehicles in the reserved lane travel in the same direction of traffic
Explanation:
A reserved lane is marked to show that a specific group of vehicles can use it, but the direction of travel in that lane remains the same as the rest of the traffic. So, vehicles in the reserved lane travel in the same direction as traffic in adjacent lanes. The sign isn’t indicating time-of-day limits or occupancy requirements by itself, and it doesn’t automatically prohibit changing lanes—you still move out of the lane when it’s safe and legal.
Question 1
Exam overview

About this Exam

Prepare with the Alberta Class 1 License Practice Exam practice quiz. This question bank includes 10 questions covering vehicle, inspection, lights, lane, and distance. Use it to review important concepts, identify knowledge gaps, and build confidence for the related exam, course, or assessment.

More details

Additional Information

Alberta Class 1 License Practice Exam

This practice set contains 10 questions from the matching question bank and focuses on vehicle, inspection, lights, lane, and distance. Work through each question carefully, review the provided solutions, and revisit topics that need more study before your next attempt.

This is an independent study resource intended for practice and review; it is not an official examination or an endorsement by any organization named in the title.

Quiz information

Frequently Asked Questions

The complete question count is available after full access is unlocked.
No fixed duration is currently configured for this quiz.
Question explanations are included where they are available in the quiz content, helping you review the reasoning after answering.
Yes. You can retake the practice test again as you continue studying during your available access period.
After your access is confirmed, you can continue into the complete practice exam from this quiz flow.
Unless explicitly stated otherwise, this page provides independent practice material for study and exam preparation and is not the official examination itself.
Keep studying

Related Questions

2nd Class Power Engineering (2A1) Practice Exam

0 min

2nd Class Power Engineering 2A3 Practice Exam

0 min

2nd Class Power Engineering (2B1) Practice Exam

0 min

2nd Class Power Engineering 2B2 Practice Exam

0 min

2nd Class Power Engineering 2B3 Practice Exam

0 min

2nd Class Power Engineering 2A2 Practice Exam Guide

0 min