2026 Kansas DMV Knowledge Test Class A Test 2 (50 Questions And Complete Answers)
1 / 50
Terms in this set
50
Steering wheel play should be no more than:
1. 10 degrees.
2. 25 degrees.
3. 50 degrees.
4. 75 degrees.
1. 10 degrees.
2. 25 degrees.
3. 50 degrees.
4. 75 degrees.
10 degrees.
When a construction worker is close to the road, you should:
1. Increase your speed.
2. Decrease your speed.
3. Not drive in any lane.
4. Wait to proceed until the construction is complete.
1. Increase your speed.
2. Decrease your speed.
3. Not drive in any lane.
4. Wait to proceed until the construction is complete.
Decrease your speed.
When driving through a work zone, you should:
1. Slow down.
2. Speed up.
3. Use a cell phone.
4. Steer with one hand to keep the other hand free.
1. Slow down.
2. Speed up.
3. Use a cell phone.
4. Steer with one hand to keep the other hand free.
Slow down.
Extremely hot temperatures can cause:
1. Tire failure.
2. A trailer to disengage.
3. Lights to malfunction.
4. Increased gas mileage.
1. Tire failure.
2. A trailer to disengage.
3. Lights to malfunction.
4. Increased gas mileage.
Tire failure.
The suspension system:
1. Holds up the vehicle and its load.
2. Keeps the load the proper distance behind the driver’s compartment.
3. Maintains a safe distance between the vehicle and other vehicles.
4. Lightens the load for the tires.
1. Holds up the vehicle and its load.
2. Keeps the load the proper distance behind the driver’s compartment.
3. Maintains a safe distance between the vehicle and other vehicles.
4. Lightens the load for the tires.
Holds up the vehicle and its load.
An air compressor governor will stop the compressor from pumping air once the air tanks have an air pressure level of:
1. 125 psi.
2. 100 psi.
3. 150 psi.
4. 80 psi.
1. 125 psi.
2. 100 psi.
3. 150 psi.
4. 80 psi.
125 psi.
Before beginning downhill, you should:
1. Shift into a higher gear.
2. Take your vehicle out of gear.
3. Shift into a lower gear.
4. Rely only on braking to reduce your speed.
1. Shift into a higher gear.
2. Take your vehicle out of gear.
3. Shift into a lower gear.
4. Rely only on braking to reduce your speed.
Shift into a lower gear.
When checking the springs during a vehicle inspection, do all of the following, except:
1. Look for missing leaf springs.
2. Look for broken coil springs.
3. Ensure torsion springs are not damaged.
4. Glue cracked leaf springs.
1. Look for missing leaf springs.
2. Look for broken coil springs.
3. Ensure torsion springs are not damaged.
4. Glue cracked leaf springs.
Glue cracked leaf springs.
9 Friction inside a brake drum is caused when the brake shoes and linings:
1. Push against each other.
2. Separate from the axle.
3. Push against the inside of the drum.
4. Create excess heat.
1. Push against each other.
2. Separate from the axle.
3. Push against the inside of the drum.
4. Create excess heat.
Push against the inside of the drum.
When checking the exhaust system, it should be:
1. Loose.
2. Leaking.
3. Fastened securely.
4. Cracked.
1. Loose.
2. Leaking.
3. Fastened securely.
4. Cracked.
Fastened securely.
Showing the first 10 terms. Use the flashcard player above to study all 50 terms!